plakar-s3-data: seed done except seafile-fs (EINTR livelock, excluded)
Seafile's block store wedged the fs walker for 12h in an lstat preemption/EINTR livelock on the live pool; coverage moves to the incus leg reading the sdb replica. Restore test + cron are the remaining steps of the data leg. Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
This commit is contained in:
Julien Lutran
co-authored by
Claude Fable 5
Claude Fable 5
parent
4b73d77803
commit
ae82d9f682
@@ -0,0 +1,193 @@
|
||||
# Archer C7: upgrade OpenWrt 19.07.4 → 25.12.5
|
||||
|
||||
> **Outcome (2026-08-20):** upgrade done (flashed clean per this doc).
|
||||
> The USB-tether flapping survived the new kernel → root cause is the
|
||||
> C7's USB port lacking charging current (phone dropped off the bus
|
||||
> whenever it drew charge). **WAN is now the phone's Wi-Fi hotspot**:
|
||||
> 2.4 GHz `radio1` in STA mode → interface `wwan` (`phy1-sta0`, in the
|
||||
> wan zone), phone on a mains charger. `usbwan` stays configured for a
|
||||
> future powered-USB-hub wired option. Post-flash gotcha: fw4 compiled
|
||||
> NAT for `eth0.2` only while `usbwan` was down at reload time — LAN
|
||||
> had no internet until `service firewall restart` with the WAN
|
||||
> interface up.
|
||||
|
||||
Home router **TP-Link Archer C7 v5** (`tplink,archer-c7-v5`, target
|
||||
`ath79/generic`, 16 MB flash / 128 MB RAM) at `192.168.0.2`, running
|
||||
OpenWrt 19.07.4 (2020, kernel 4.14, EOL since 2022). Target release:
|
||||
**OpenWrt 25.12.5** (kernel 6.12.94, firewall4/nftables, `apk` package
|
||||
manager instead of `opkg`).
|
||||
|
||||
Context (2026-08-19): after a reboot the router came up with **dnsmasq,
|
||||
firewall and odhcpd disabled** (missing `/etc/rc.d/` symlinks — no DHCP,
|
||||
no NAT). All three were restarted and re-enabled, but the incident plus
|
||||
the EOL release motivated this upgrade. A fresh flash also rules out
|
||||
any other overlay damage.
|
||||
|
||||
Current setup worth knowing:
|
||||
|
||||
- **WAN = OPPO phone (SM8350) USB-tethered** on `usb0` via RNDIS
|
||||
(`kmod-usb-net-rndis`), interface `usbwan`, DHCP from the phone
|
||||
(10.205.61.0/24). The ethernet WAN port is unused — the ISP box at
|
||||
`.1` is dead, which is also why the router LAN IP is `.2`.
|
||||
- SSH: `ssh -i id_rsa_claude root@192.168.0.2` (key at perso repo root;
|
||||
19.07's dropbear needs
|
||||
`-o HostKeyAlgorithms=+ssh-rsa -o PubkeyAcceptedAlgorithms=+ssh-rsa`
|
||||
from a modern OpenSSH; 25.12 won't)
|
||||
- DNS: dnsmasq forwards everything to **blocky** at `192.168.0.254`
|
||||
(`noresolv` + `server=192.168.0.254`), and DHCP option 6 hands blocky
|
||||
directly to clients
|
||||
- Wi-Fi: 5 GHz only (`radio0`, ch 36, VHT80, SSID `HOME`, WPA2-PSK);
|
||||
2.4 GHz radio disabled
|
||||
- 7 static DHCP leases (see script below)
|
||||
- Only user-installed packages on 19.07: `kmod-usb-net-rndis` + deps
|
||||
|
||||
## Prerequisites (done 2026-08-19)
|
||||
|
||||
- [x] Config backup: `sysupgrade -b` → `~/code/perso/backup-archer-c7-20260819.tar.gz`
|
||||
(laptop; contains Wi-Fi PSK and dropbear host keys — never commit)
|
||||
- [x] Firmware `openwrt-25.12.5-ath79-generic-tplink_archer-c7-v5-squashfs-sysupgrade.bin`
|
||||
downloaded, **sha256 verified** (`f15b16b3…`) against the release
|
||||
`sha256sums`, staged in `~/code/perso/archer-c7-upgrade/` and on
|
||||
the router at `/tmp/` (`/tmp` is RAM — gone after any reboot,
|
||||
re-`scp` if needed)
|
||||
- [x] **Offline driver packages** staged in `~/code/perso/archer-c7-upgrade/`:
|
||||
`kmod-mii`, `kmod-usb-net`, `kmod-usb-net-cdc-ether`,
|
||||
`kmod-usb-net-rndis` (all `6.12.94-r1.apk`). Critical: the phone
|
||||
tether is the only WAN and the RNDIS driver is **not** in the
|
||||
default image, so after flashing the router has no internet to
|
||||
install it from — it must be `scp`'d in.
|
||||
|
||||
## Upgrade
|
||||
|
||||
**Do not keep settings across this jump** (19.07 → 25.12 spans the
|
||||
fw3→fw4 and network-syntax migrations). Flash clean with `-n` and
|
||||
reconfigure with the script below.
|
||||
|
||||
You need the **laptop on ethernet** to a LAN port: the fresh image
|
||||
boots at `192.168.1.1` with Wi-Fi disabled.
|
||||
|
||||
```sh
|
||||
# on the router — image already in /tmp, verify then flash
|
||||
sha256sum /tmp/openwrt-25.12.5-ath79-generic-tplink_archer-c7-v5-squashfs-sysupgrade.bin
|
||||
# expect f15b16b36df7fce8a5cf1302320fdb428c3bb6fbc2949a4858afa257f4f364a2
|
||||
sysupgrade -n -v /tmp/openwrt-25.12.5-ath79-generic-tplink_archer-c7-v5-squashfs-sysupgrade.bin
|
||||
```
|
||||
|
||||
The router reboots (~3 min, don't power-cycle). Then from the laptop
|
||||
(ethernet, DHCP gives a 192.168.1.x address):
|
||||
|
||||
```sh
|
||||
# passwordless root at first boot — set a password and install the key
|
||||
ssh root@192.168.1.1 # no password
|
||||
passwd
|
||||
mkdir -p /etc/dropbear && exit
|
||||
scp ~/code/perso/id_rsa_claude.pub root@192.168.1.1:/etc/dropbear/authorized_keys
|
||||
|
||||
# push the offline RNDIS drivers
|
||||
scp ~/code/perso/archer-c7-upgrade/kmod-*.apk root@192.168.1.1:/tmp/
|
||||
```
|
||||
|
||||
## Reconfigure
|
||||
|
||||
Run on the router. Single source of truth for the whole config;
|
||||
`<wifi-psk>` is in the backup tarball (`etc/config/wireless`).
|
||||
|
||||
```sh
|
||||
#!/bin/sh
|
||||
set -eux
|
||||
|
||||
# RNDIS drivers (offline — phone tether is the only WAN)
|
||||
apk add --allow-untrusted /tmp/kmod-mii-*.apk /tmp/kmod-usb-net-6*.apk \
|
||||
/tmp/kmod-usb-net-cdc-ether-*.apk /tmp/kmod-usb-net-rndis-*.apk
|
||||
|
||||
# --- network: keep the generated switch/bridge config, change only what we need
|
||||
uci set network.lan.ipaddr='192.168.0.2'
|
||||
uci set network.usbwan=interface
|
||||
uci set network.usbwan.proto='dhcp'
|
||||
uci set network.usbwan.device='usb0'
|
||||
uci commit network
|
||||
|
||||
# --- firewall: usbwan joins the wan zone (zone[1] = 'wan' in the default config)
|
||||
uci add_list firewall.@zone[1].network='usbwan'
|
||||
uci commit firewall
|
||||
|
||||
# --- dhcp/dns: forward to blocky, hand blocky to clients, static leases
|
||||
uci set dhcp.@dnsmasq[0].noresolv='1'
|
||||
uci add_list dhcp.@dnsmasq[0].server='192.168.0.254'
|
||||
uci add_list dhcp.lan.dhcp_option='6,192.168.0.254'
|
||||
add_host() {
|
||||
uci add dhcp host >/dev/null
|
||||
uci set dhcp.@host[-1].mac="$1"
|
||||
uci set dhcp.@host[-1].ip="$2"
|
||||
uci set dhcp.@host[-1].name="$3"
|
||||
uci set dhcp.@host[-1].dns='1'
|
||||
}
|
||||
add_host 'F4:5C:89:BE:C1:C3' '192.168.0.20' 'LAPTOP719974'
|
||||
add_host '10:66:6A:87:A1:49' '192.168.0.254' 'blocky'
|
||||
add_host '10:66:6A:C8:E1:0A' '192.168.0.5' 'jellyfin-server'
|
||||
add_host '10:66:6A:FF:59:1C' '192.168.0.6' 'jellyfin-client'
|
||||
add_host '10:66:6A:85:20:B7' '192.168.0.11' 'privoxy'
|
||||
add_host '10:66:6A:55:9F:10' '192.168.0.7' 'transmission-bt'
|
||||
add_host '50:9A:4C:20:D9:2B' '192.168.0.21' 'patate'
|
||||
uci commit dhcp
|
||||
|
||||
# --- wifi: 5 GHz AP as before, upgraded to WPA2/WPA3 mixed; 2.4 GHz stays off
|
||||
uci set wireless.radio0.channel='36'
|
||||
uci set wireless.radio0.htmode='VHT80'
|
||||
uci set wireless.radio0.disabled='0'
|
||||
uci set wireless.default_radio0.ssid='HOME'
|
||||
uci set wireless.default_radio0.encryption='sae-mixed'
|
||||
uci set wireless.default_radio0.key='<wifi-psk>'
|
||||
uci set wireless.default_radio0.network='lan'
|
||||
uci commit wireless
|
||||
|
||||
reload_config
|
||||
/etc/init.d/network restart
|
||||
```
|
||||
|
||||
The LAN IP change kicks you off; reconnect at `192.168.0.2` (plug the
|
||||
phone back in for WAN).
|
||||
|
||||
## Verify
|
||||
|
||||
```sh
|
||||
ssh root@192.168.0.2
|
||||
ifstatus usbwan | grep -E 'up|address' # up:true, 10.205.61.x
|
||||
ping -c2 8.8.8.8 && ping -c2 openwrt.org # WAN + DNS via blocky
|
||||
nft list chain inet fw4 srcnat_wan # masquerade on usbwan
|
||||
ls /etc/rc.d/ | grep -E 'dnsmasq|firewall|odhcpd' # all enabled
|
||||
```
|
||||
|
||||
Then from a LAN client: renew DHCP (expect 192.168.0.100–249, DNS
|
||||
`.254`), check internet, check the static leases land on their IPs.
|
||||
|
||||
## Known issue: 5 GHz `ath10k-ct`
|
||||
|
||||
The C7 v2/v5 has a long-standing 5 GHz issue with the default
|
||||
`ath10k-ct` driver: `SWBA overrun on vdev 0` log spam plus client
|
||||
drops under some loads. **Only if it shows up**, swap to the non-ct
|
||||
driver (needs working WAN, or pre-download the same way as the RNDIS
|
||||
apks):
|
||||
|
||||
```sh
|
||||
apk del kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
||||
apk add kmod-ath10k ath10k-firmware-qca988x
|
||||
reboot
|
||||
```
|
||||
|
||||
## Recovery
|
||||
|
||||
If the flash bricks: C7 v5 has TFTP recovery — hold **Reset** while
|
||||
powering on, router pulls `ArcherC7v5_tp_recovery.bin` (the OpenWrt
|
||||
**factory** image renamed to that) from a TFTP server at
|
||||
`192.168.0.66`. Factory image is in the same release directory as the
|
||||
sysupgrade one.
|
||||
|
||||
## Post-upgrade cleanup
|
||||
|
||||
- Delete `/tmp` copies (automatic on reboot)
|
||||
- Keep `~/code/perso/backup-archer-c7-20260819.tar.gz` until the new
|
||||
setup has survived a reboot + a few days
|
||||
- `~/code/perso/archer-c7-upgrade/` can go once the RNDIS drivers are
|
||||
installed and Wi-Fi is confirmed stable (or keep the apks in case of
|
||||
a re-flash)
|
||||
Reference in New Issue
Block a user